The Cray System Management (CSM) operational activities are administrative procedures required to operate an HPE Cray EX system with CSM software installed.
The following administrative topics can be found in this guide:
Important procedures for configuring, managing, and validating the CSM environment.
General information on what needs to be done before the initial install of CSM.
Build and customize image recipes with the Image Management Service (IMS).
aarch64 ImagesUse the Boot Orchestration Service (BOS) to boot, configure, and shut down collections of nodes.
Procedures required for a full power off of an HPE Cray EX system.
Additional links to power off sub-procedures provided for reference. Refer to the main procedure linked above before using any of these sub-procedures:
Procedures required for a full power on of an HPE Cray EX system.
Additional links to power on sub-procedures provided for reference. Refer to the main procedure linked above before using any of these sub-procedures:
HPE Cray System Management (CSM) software manages and controls power out-of-band through Redfish APIs.
Use the Ceph Object Gateway Simple Storage Service (S3) API to manage artifacts on the system.
NOTE CRUS was deprecated in CSM 1.2.0 and removed in CSM 1.5.0. See the following links for more information:
The Configuration Framework Service (CFS) is available on systems for remote execution and configuration management of nodes and boot images.
session_ttlThe system management components are broken down into a series of micro-services. Each service is independently deployable, fine-grained, and uses lightweight protocols. As a result, the system’s micro-services are modular, resilient, and can be updated independently. Services within the Kubernetes architecture communicate using REST APIs.
kubectl
containerdFailed to start etcd on Master NCNRepositories are added to systems to extend the system functionality beyond what is initially delivered. The Sonatype Nexus Repository Manager is the primary method for repository management. Nexus hosts the Yum, Docker, raw, and Helm repositories for software and firmware content.
Mechanisms used by the system to ensure the security and authentication of internal and external requests.
kcadm.shHPE Cray EX systems are designed so that system management services (SMS) are fully resilient and that there is no single point of failure.
StatefulSet Pods on Another NodeConMan is a tool used for connecting to remote consoles and collecting console logs. These node logs can then be used for various administrative purposes, such as troubleshooting node boot issues.
Ceph is the utility storage platform that is used to enable pods to store persistent data. It is deployed to provide block, object, and file storage to the management services running on Kubernetes, as well as for telemetry data coming from the compute nodes.
ceph-upgrade-tool Usage<none>HEALTH_ERR Module devicehealth has failed table Device already existsEnable system administrators to assess the health of their system. Operators need to quickly and efficiently troubleshoot system issues as they occur and be confident that a lack of issues indicates the system is operating normally.
prometheus-kafka-adapter errors during installationgrok-exporter errors during installationThe System Layout Service (SLS) holds information about the system design, such as the physical locations of network hardware, compute nodes, and cabinets. It also stores information about the network, such as which port on which switch should be connected to each compute node.
The System Configuration Service (SCSD) allows administrators to set various BMC and controller parameters. These parameters are typically set during discovery, but
this tool enables parameters to be set before or after discovery. The operations to change these parameters are available in the Cray CLI under the scsd command.
Use the Hardware State Manager (HSM) to monitor and interrogate hardware components in the HPE Cray EX system, tracking hardware state and inventory information, and making it available via REST queries and message bus events when changes occur.
The Hardware Management (HM) Collector is used to collect telemetry and Redfish events from hardware in the system.
Procedures for managing and setting up HPE PDUs.
Monitor and manage compute nodes (CNs) and non-compute nodes (NCNs) used in the HPE Cray EX system.
DiscoveryCheck for Redfish Events from NodesOverview of the several different networks supported by the HPE Cray EX system.
HPE Cray EX systems can have network switches in many roles: spine switches, leaf switches, LeafBMC switches, and CDU switches. Newer systems have HPE Aruba switches,
while older systems have Dell and Mellanox switches. Switch IP addresses are generated by Cray Site Init (CSI).
The customer accessible networks (CMN/CAN/CHN) provide access from outside the customer network to services, NCNs, and User Access Nodes (UANs) in the system.
The DHCP service on the HPE Cray EX system uses the Internet Systems Consortium (ISC) Kea tool. Kea provides more robust management capabilities for DHCP servers.
The central DNS infrastructure provides the structural networking hierarchy and datastore for the system.
ncsd on UANsExternal DNS, along with the Customer Management Network (CMN), Border Gateway Protocol (BGP), and MetalLB, makes it simpler to access the HPE Cray EX API and system management services. Services are accessible directly from a laptop without needing to tunnel into a non-compute node (NCN) or override /etc/hosts settings.
csi config init Input Valuescmn-external-dns Value Post-InstallationMetalLB is a component in Kubernetes that manages access to LoadBalancer services from outside the Kubernetes cluster. There are LoadBalancer services on the Node
Management Network (NMN), Hardware Management Network (HMN), and Customer Access Network (CAN).
MetalLB can run in either Layer2-mode or BGP-mode for each address pool it manages. BGP-mode is used for the NMN, HMN, and CAN. This enables true load balancing
(Layer2-mode does failover, not load balancing) and allows for a more robust layer 3 configuration for these networks.
Spire provides the ability to authenticate nodes and workloads, and to securely distribute and manage their identities along with the credentials associated with them.
The Firmware Action Service (FAS) provides an interface for managing firmware versions of Redfish-enabled hardware in the system. FAS interacts with the Hardware State Manager (HSM), device data, and image data in order to update firmware.
See Update Firmware with FAS for a list components that are upgradable with FAS. Refer to the HPC Firmware Pack (HFP) product stream to update firmware on other components.
FASUpdate Scriptm001v2.78NOTE: The User Access Service is deprecated in CSM 1.5.2 and will be removed in CSM 1.6.
The User Access Service (UAS) is a containerized service managed by Kubernetes that enables application developers to create and run user applications. Users launch
a User Access Instance (UAI) using the cray command. Users can also transfer data between the Cray system and external systems using the UAI.
macvlans Network AttachmentsContainerCreating/etc/sssd/sssd.confThe System Admin Toolkit (SAT) is a command-line interface that can assist administrators with common tasks, such as
troubleshooting and querying information about the HPE Cray EX System, system boot and shutdown, and replacing hardware
components. In CSM 1.3 and newer, the sat command is available on the Kubernetes NCNs without installing the SAT
product stream.
The Install and Upgrade Framework (IUF) provides a CLI and API which automates operations required to install, upgrade
and deploy non-CSM product content onto an HPE Cray EX system. Each product distribution includes an iuf-product-manifest.yaml
file which IUF uses to determine what operations are needed to install, upgrade, and deploy the product.
Information on how to perform backups of individual services or the entire system, and how to restore from these backups.