Software Management Services health checks

SMS test execution

This test requires that the Cray CLI is configured on nodes where the test is executed. See Cray command line interface.

This test can be run on any Kubernetes NCN (any master or worker NCN, but not the PIT node). When run on a Kubernetes master NCN, the TFTP file transfer subtest is omitted. However, that TFTP subtest is run on a worker NCN as part of the Goss NCN health checks.

(ncn-mw#) The following command runs the entire SMS test suite (with the possible exception of the TFTP file transfer subtest, as noted in the previous paragraph).

/usr/local/bin/cmsdev test -q all
  • The cmsdev tool logs to /opt/cray/tests/install/logs/cmsdev/cmsdev.log
    • This was a change in CSM 1.4. In CSM releases prior to 1.4, the log file location was /opt/cray/tests/cmsdev.log
  • The -q (quiet) and -v (verbose) flags can be used to decrease or increase the amount of information sent to the screen.
    • The same amount of data is written to the log file in either case.

Interpreting cmsdev results

  • If all checks are passed, the following will be true:
    • The return code will be zero.
    • The final line of output will begin with SUCCESS.
      • For example: SUCCESS: All 6 service tests passed: bos, cfs, conman, ims, tftp, vcs
  • If one or more checks are failed, the following will be true:
    • The return code will be non-zero.
    • The final line of output will begin with FAILURE and lists the failed checks.
      • For example: FAILURE: 2 service tests FAILED (conman, ims), 4 passed (bos, cfs, tftp, vcs)
    • After remediating a test failure for a particular service, just that single service test can be rerun by replacing all in the cmsdev command line with the name of the service. For example: /usr/local/bin/cmsdev test -q cfs

Additional test execution details can be found in /opt/cray/tests/install/logs/cmsdev/cmsdev.log.

Version

(ncn-mw#) The following command displays the version of the cmsdev test tool.

/usr/local/bin/cmsdev version

Known issues with SMS tests

Cray CLI

Some of the subtests may fail if the Cray CLI is not configured on the management NCN where cmsdev is executed. See the following for more information:

Invalid CFS component

If a CFS component exists with a zero-length string for its id field, then it may cause the cmsdev CFS subtest to fail. The cmsdev test failure symptom will depend on the version of cmsdev being run. (See the Version section above for details on how to find the version).

  • For cmsdev versions 1.25 or higher, the CFS subtest failures will resemble the following:

    ERROR (run tag fhn3C-cfs): In first item listed, 'id' field maps to a 0-length string, but it should have non-0 length

  • For cmsdev versions less than 1.25 but at least 1.16.2, the CFS subtest failures will resemble the following:

    ERROR (run tag sosdD-cfs): GET https://api-gw-service-nmn.local/apis/cfs/v3/components/: expected status code 200, got 404
ERROR (run tag sosdD-cfs): GET https://api-gw-service-nmn.local/apis/cfs/v2/components/: expected status code 200, got 404
ERROR (run tag sosdD-cfs): CLI command (cfs v3 components describe  --format json) failed with exit code 2
ERROR (run tag sosdD-cfs): CLI command (cfs v2 components describe  --format json) failed with exit code 2

  • For cmsdev versions less than 1.16.2, the CFS subtest failure will resemble the following:

    ERROR (run tag fhn3C-cfs): First list item has empty value for "id" field

For details on how to correct this problem, see CFS Component With Zero-Length ID.